Application

Application

Control an assortment of HVAC and lighting applications as well as monitor any digital or analog point. The UBM is ideal for applications that require open protocols, high I/O concentration, or sophisticated HVAC control strategies.

Specifications

Specifications

Mounting

DIN Rail Mount OR Surface-mount in a control panel using four slotted screw holes

Dimensions

• Height: 5.45 inches
• Width: 6.85 inches
• Depth: 2.26 inches

Power Requirements

• Input: 20-30 VAC, Class 2
• Frequency: 50/60 Hz
• Consumption: 5 VA

Inputs
Universal (6 Points):

• 0-10V DC, 20K NTC, 4-20mA
• These Universal Input points can be configured to the above voltage, resistance, and current ranges. These can be used for temperature, humidity, CO2, or relative humidity depending on the chosen sensor.

Digital (4 Points):

• Voltage Rating: 0 to 30 Vdc open circuit
• Input Type: Dry contact to detect open and closed circuit
• Operating Range: Open circuit = False; Closed circuit = True
• Resistance: Open circuit > 3,000 Ohms; Closed circuit < 500 Ohms

Outputs
Analog (3 Points – can be either current or voltage)

Current

• Current Output Range: 4.0 to 20.0 mA
• Output Load Resistance: 550 Ohms maximum

Analog outputs may be configured as digital outputs and operate as follows:

• False (0%): produces the min possible value of 0 mA
• True (100%): produces the max possible value of 22 mA

Voltage

• Voltage Output Range: 0.0 to 10.0 Vdc
• Maximum Output Current: 10.0 mA

Analog outputs may be configured as digital outputs and operate as follows:

• False (0%): produces the min possible value of 0 Vdc
• True (100%): produces the max possible value of 11 Vdc

Digital (8 Points - Triac)

• Voltage Rating: 20 to 30 Vac @ 50/60Hz
• Current Rating: 25 mA to 500 mA continuous, and 800 mA (AC rms) for
• 60 milliseconds

Communications

• Method: RS-485
• Application Protocol: BACnet MSTP, maximum 76.8 Kbps
• Method: Two-Wire
• Application Protocol: Sylk™ Bus for supported wall sensors

Operating Environment

• Temperature: -40° to 150°F (-40°C to 68.5°C)
• Humidity: 5% to 95% RH, non-condensing

Approvals

• UL/cUL (E87741) listed under UL916 (Standard for Open Energy Management Equipment) with plenum rating. CSA (LR95329-3) listed.
• Meets FCC Part 15, Subpart B, Class B (radiated emissions) requirements.
• Meets Canadian standard C108.8 (radiated emissions).

Conforms to the following requirements per European Consortium standards:

• EN 61000-6-1; 2001 (EU Immunity).
• EN 61000-6-3; 2001 (EU Emissions)
• BTL B-ASC (BACnet Testing Laboratories, BACnet Application Specific Controller)

Application Requirements

• Opus Version 5.8 or higher
• Application Version 4.0 or higher
• NovarNet.jar version 2.6 or higher
• UnitConversion.jar
• docUBM.jar
• genericUIFramework.jar
• ubmSupport.jar
• ubmTool.jar
• ubm.jar

LED Indicators

There is a single LED indicator with the following statuses denoted:

• LED State Blink Rate Status or Condition
• FF Not applicable No power to processor, LED damaged, low voltage to board, first second of power up or loader damaged.

ON ON steady; not blinking Processor not operating. Application Program CRC being checked.

• This takes 1-2 seconds and occurs on each restart (power up, reset and reflash, and following configuration file download).
• Very Slow Blink 1 second ON, Controller is operating normally.
  (continuous) 1 second OFF
• Slow Blink 0.5 second ON, Controller alarm is active or is in the process (continuous) 0.5 second OFF of configuration file download.
• Medium Blink 0.3 second ON, Controller is in reflash mode or awaiting/receiving reflash (continuous) 0.3 second OFF data via the BACnet network.

Product Order Numbers